Electrolux Dryer Repair

How to Repair A Electrolux Dryer?

If the error E64 is keeping you from drying clothes or heating up, you’re probably wondering how to repair an Electrolux dryer. This article will provide you with information on the three common parts of a dryer. This includes the igniter, thermal fuse, and gas valve solenoid. If none of these is the problem, you can try a few of the other common electrolux dryer repair techniques. But if none of them work, you may need to replace the entire machine or hire a dryer appliance repair company in scarborough.

Error code E64 prevents your dryer from heating up or drying clothes

If your Electrolux dryer is not heating up or drying your clothes properly, you may encounter error code E64. This error may occur if the moisture sensor is too high or if the wiring is damaged. To repair this problem, unplug the machine from the wall and examine the wiring harnesses. If you notice any damaged wire harnesses, replace them immediately.

A malfunctioning heating element is the most likely cause of an error code E64. This component is responsible for heating air in the drum. The heating element should be replaced if it is faulty. Otherwise, it is best to call a technician to check the wiring. A defective thermal fuse will prevent the heating element from engaging. If you cannot replace the heating element, you can try checking the thermal fuse.

Checking the thermal fuse

Before checking the thermal fuse when repairing an Electrolux dryer, you must turn off the power source. Unplug the machine from the wall outlet or from the fuse box. You can also flip the circuit breaker switch in the panel. Checking the thermal fuse is similar to testing the thermostat in your dryer. You must remove the metal slip-on connectors that connect the thermal fuse with the dryer’s circuit board. You may also need to remove the front panel or drum of the dryer to access the thermal fuse.

You can check the thermal fuse easily with the help of an electrical multi-tester. To test the fuse, you must place the probe near the terminals of the thermal fuse. If the reading is infinity, the thermal fuse is working properly. If it reads below this value, it is triggered. This simple process may take a few minutes. If you’re in a hurry, you can also consult a service manual or consult a repairman.

Checking the igniter

If you’re having trouble heating your clothes in an electrolux dryer, you might want to check the igniter first. This part of the dryer is responsible for igniting gas during the drying process. If it fails to light, your dryer will not produce any heat. To determine if the igniter is the problem, use a multimeter to check for continuity. If it doesn’t, replace it.

The igniter is located next to the burner tube. It may be flat or coil-shaped. Before attempting to change it, be sure to handle it carefully. To check the igniter, take out a multimeter and set the resistance to its lowest setting. Then, touch the probes to the igniter’s terminals. The resistance of the igniter should be 50-400 ohms, and readings outside of this range are usually indicative of a malfunction.

Checking the gas valve solenoid

If your Electrolux dryer is not heating up, you should check the gas valve solenoid to determine if this is the issue. A defective solenoid will prevent the gas from passing through to the ignitor. You can access the solenoid using a screwdriver and check for continuity. If it shows continuity, the igniter is working properly. If not, you should purchase a new solenoid from the manufacturer.

To replace the solenoid, you should disassemble your dryer. You should be able to get to it through the top or outside door. This part is easy to access and has two lead wires. If you are unable to locate the solenoid, you can check the electrical connection with a multimeter. The multimeter should read zero. If it does not, replace the solenoid with a new one of the same type.

Checking the drum roller axle

One of the easiest ways to troubleshoot your Electrolux dryer is to check the drum roller axle. The drum roller axle acts as the drive mechanism for the drum and is a major component in the drying process. If it doesn’t rotate smoothly, it may need to be replaced. If it’s loose or damaged, you should try to remove it from the machine and inspect it closely. Then, contact an Electrolux dryer repair expert to get the problem fixed.

If the drum rollers are worn, you may need to replace them. However, you don’t need to replace the axle itself. The roller shaft should be cleaned thoroughly before you install new rollers. Check the drum roller axle carefully for worn or damaged rollers. You don’t need to replace the entire roller shaft, but if you’re replacing the drum rollers, you should take a look at the drum support rollers as well. The axles are what hold the drum in place. If the rollers are worn, they could cause the motor to overload and fail.